Clear All

PLIERS SPARK PLUG WIRE

0 out of 5

Spark Plug Wire Pliers Offers Easy and Safe Way to Remove Spark Plugs Even While Engine Runs Featuring Ruggedly Crafted Handles and Jaws Insulated Design Offers Protection from Shock Jaws Engineered with Small Indentations Allowing for Gripping Bare Terminals Overall Length (mm): 190

R97.81
Add to basket
Add to wishlist

SOCKET SET INJECTOR 4PC

0 out of 5

Injector Socket Set 4 Pc For removing the electrical unit of injectors. Deep sockets with wide cut-out. For Use On – Alfa Romeo, Chrysler, BMW, Ford, VW, Mercedes, Audi, Opel, Vauxhall, Seat, Volvo, Rover Also On Volvo, Man 2.5td & Scania HGVS. 22mm Injector Socket (6Pt) * 110mm 22mm Injector Socket (12Pt) * 75mm 27mm Injector Socket (12Pt) * 78mm 28mm Injector Socket (12Pt) * 78mm

R614.79
Add to basket
Add to wishlist

PLIERS CV BOOT CLAMP

0 out of 5

CV Boot Clamp For tightening ear-type CV boot clamps. Strong and durable. Fits CV joint boots, also installs perma-quick clamps. Ideal to install clamps in fuel filters, water pumps, boots for CV joints and other hoses of the cooling system. Length (mm): 250

R163.01
Add to basket
Add to wishlist

PLIERS PANEL CLIP REMOVER

0 out of 5

Positive Lift Action Clip Removal Pliers Allows easy access and removal of those hard to reach clips on bumper covers, fender liners etc. Features positive lift action without damage to the clip or the surrounding area. Simply insert the jaws under the clip and squeeze the pliers to remove the clip. Length (mm): 240

R181.64
Add to basket
Add to wishlist

PLIERS SNAP RING INT/EXT

0 out of 5

Combination Internal / External Snap Ring Pliers 190mm The internal external snap ring pliers come with four pairs of replacement tips, including two straight tips, one pair of 90° tips and one pair of 45°tips. Snap rings or retaining rings hold components or assemblies onto a shaft or in a housing when installed in a groove. You'll get the job done more quickly with snap ring pliers without putting in overtime. * Internal external snap ring pliers provides grip on various rings * Steel pliers with plastic grips * Use on internal and external snap rings * Includes four pairs of replacement tips: two straight tips, one 90° tip and one 45° tip.

R228.22
Add to basket
Add to wishlist

COIL SPRING COMPRESSOR EXTERNAL

0 out of 5

External Coil Spring Compressor Set Removes and installs coil springs where removal through the center of the spring is not possible Services both Straight & Curved Coil Springs Includes U-bolts & wing nuts Maximum diameter spring that the hooks will accommodate is 0.75". Diameter of the rod: 5/8" INSTRUCTIONS FOR STRAIGHT COIL SPRINGS:

  1. Install 3 leg assemblies evenly around the spring. Turn nuts finger-tight to hold in position.
  2. Install one U-bolt near the center of each leg with open end pointing away from the spring. Place the bar and wing nuts on the U-bolt, then finger-tighten the wing nuts
  3. Tighten each leg nut a little at a time to compress spring gradually. Do not over-compress.
  4. To release the compressor, loosen each leg nut a little at a time.
INSTRUCTIONS FOR CURVED COIL SPRINGS:
  1. With the car raised and safely supported, place a jack under the lower control arm.  Raising the jack will compress the spring.
  2. Install as many leg assemblies and safety U-bolts as possible (see #1 & #2 above), then finger-tighten the leg nuts.
  3. Disconnect the lower control arm bolts, then slowly lower the jack until the spring can be removed.  The curved contour will remain.
  4. To install a new coil spring, use one or more legs and U-bolts to produce the necessary curve.

R433.15
Add to basket
Add to wishlist

COIL SPRING COMPRESSOR MACPHERSON

0 out of 5

MacPherson Strut Coil Spring Compressor Set The Strut Coil Spring Compressor is used for safe and easy removal and installation of coil springs from MacPherson struts. Compressor design includes U-bolts that securely attach tool to spring during operation for maximum safety. * Can't use with any impact or power tools * ONLY for MacPherson struts

R824.38
Add to basket
Add to wishlist

PLIERS HOSE CLAMP ANGLED

0 out of 5

Angled Flat Nose Hose Clamp Pliers 45° Angle offset head enables the flat band hose clamp pliers to remove and install clamps in hard to reach areas. Pliers feature rotating angled jaws to hold clamp at any angle, a ratchet locking mechanism to hold clamp at any angle, and a ratchet locking mechanism to hold clamps in the open position.

R260.82
Add to basket
Add to wishlist

PLIERS HOSE PINCHING

0 out of 5

Hose Pinching Pliers 160mm Special radius jaws to avoid damaging hoses Lightweight and non-conductive material Great tool for all flexible hoses. Can be used on brakes, fuel, heater, radiator and water lines. Capacity is 1/4" to 3/4" (6 - 19mm)

R102.47
Add to basket
Add to wishlist

TESTER RADIATOR PRESSSURE 8PC

0 out of 5

Radiator Cap Pressure Tester 8 Pc Cooling system & radiator cap pressure tester fit most standard radiator caps and will test pressures up to 30 psi. This allows for pressure testing of almost any cooling system to help determine leak location and cooling system condition. Specification: No 1: Gm 4 cylinder (Buick, Chevrolet, Oldsmobile, Pontiac, Cadillac) No 2: Truck No 3: Mercedes-Benz, Ford, Chrysler, GM, Jeep, Truck, Peugeot. No 4: Acura, Dodge, Eagle, Geo, Honda, Ford, Isuzu, Lexus, Mazda, Mitsubishi, Suzuki, Toyota, Infiniti, Nissan, GM (Nova, Spectrum, Sprint), Chrysler, Peugeot. No 5: Toyota, Honda, Mitsubishi, Suzuki Lexus, Chrysler, Acura, Dodge, Geo. “2,3” Cap adapter (testing the pressure cap) “4,5” Cap adapter (testing the pressure cap) Cooling System Pump

R4,387.37
Add to basket
Add to wishlist

TESTER RADIATOR PRESSURE14PC

0 out of 5

Universal Radiator Pressure Tester 14 Piece The universal radiator test kit helps you to diagnose problems with your cooling system. To test the operation of your radiator pressurise the cooling system to check for leaking hoses, leaking radiator, cracks in header tanks or more significant problems like water pump seal failure, blown head gasket or cracked head. This easy to use kit contains a thermometer, 4 of the most popular sized radiator cap adapters, 8 threaded adapters, hand pressure pump with gauge and pressure release valve. Applicable Models: Adapter for GM (Cadillac) Adapter for Benz, Jeep, GM (Buick) Adapter for Peugeot, Subaru, Chrysler, Acura, Mitsubishi, Nissan, Mazda, Toyota, Infiniti, Geo, Suzuki, Isuzu, GM (Nova, Spectrum, Sprint) Adapter for Honda, Toyoyta, Suzuki, Mitsubishi, Chrysler, Acura Adapter for Benz (ML-Class), GM (Achiva, Skylark, Gramd AM-1992-2002) Adapter for Volvo, Saab, Sterling, Citron, Renault, Fiat, Alfa, Jeep Adapter for VW (Jetta, T4, 1996-Passat, Golf) Adapter for Audi (A4, A6), BMW 345, VW (Passat 1997-2002) Adapter for BMW Adapter for Audi, VW Adapter for Ford, International, GM, Rover Adapter for Benz

R3,134.50
Add to basket
Add to wishlist

TESTER DIESEL COMPRESSION

0 out of 5

Diesel Compression Tester Comprehensive test kit for both direct and indirect diesel injected cars Simple and easy to use Checks engine compression under cranking conditions Small profile, quick coupling adapters for speed & security Built-in pressure relief valve enables repeat tests without dismantling Flexible hose (355mm) gives access to restricted plug & injector ports Dual scale 80mm dia gauge 0-1000psi (0-70bar) Glowplug Adapter M10 x 1.25 Glowplug Adapter M12 x 1.25 Dummy Injector M21 Dummy Injector M24 x 2.0 Standard Dummy M19 Application: BMW, Mercedes-Benz, Carbodies, Mitsubishi, Citroen, Nissan, Dacia, Opel, Daihatsu, Peugeot, Fiat, Renault, Ford, Rover, Holden, Seat, Isuzu, Toyota, Land Rover, Vauxhall, Leyland / Daf, Volkswagen, Mazda, Volvo…etc.

R4,392.02
Add to basket
Add to wishlist